H3c-technologies H3C SecPath F5000-A5 Firewall User Manual Page 35
- Page / 121
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
25
• Stateful failover can be implemented between only two devices. Use a network cable to directly
connect the failover interfaces. No intermediary device (such as a router, a switch, or a hub) is
allowed between the interfaces.
For more information about stateful failover, see the configuration guide of the firewall.
Figure 21 Network diagram for stateful failover
Connecting Ethernet cables
Connecting a copper Ethernet port
You can use category-5 or above twisted pair cables to connect the 10Base-T/100Base-TX/1000Base-T
ports on the firewall to the network. These ports use RJ-45 connectors and support MDI/MDI-X
auto-sensing. For more information about twisted pair cables, see "Ethernet twisted pair cable."
T
o connect a 10Base-T/100Base-TX/1000Base-T port to a peer device:
1. Plug one end of a twisted pair cable into the port.
2. Plug the other end of the twisted pair cable into the RJ-45 Ethernet port of the peer device.
3. Examine the port LED status.
For more information about the LED status, see "Appendix B LEDs."
A
fter you connect the firewall to the network, execute the ping or tracert command to test network
connectivity. For more information about the commands, see the command reference of the firewall.
Connecting a fiber port
W
ARNING!
Do not stare into any fiber port when you connect an optical fiber. The laser li
g
ht emitted from the optical
fiber may hurt your eyes.
CAUTION:
• Be sure to install the dust cover if the fiber port is not connected to a fiber connector.
• Never bend or curve a fiber when connecting it. The bend radius must be at least 10 cm (3.94 in).
• Keep the end of the fiber clean.
• Make sure the Tx and Rx ends of the SFP/XFP transceiver module are correctly connected.
Before you connect a fiber port, install a transceiver module to the firewall and then install the fiber
connector to the transceiver module. Transceiver modules are user supplied.
The F5000-A5 has SFP and XFP fiber ports, which only support LC connectors. The procedures for
connecting SFP and XFP fiber ports are similar. The following uses the SFP port on an NSQ1GT8C40 as
an example.
- H3C SecPath F5000-A5 Firewall 1
- Preface 3
- GUI conventions 4
- Symbols 4
- Network topology icons 4
- Port numbering in examples 4
- Obtaining documentation 5
- Technical support 5
- Documentation feedback 6
- Contents 7
- Preparing for installation 11
- Laser safety 12
- Handling safety 12
- Weight support 12
- Temperature and humidity 13
- Cleanness 13
- Cooling 14
- ESD prevention 14
- Lightning protection 16
- Rack installation 16
- Accessories 17
- Installing the firewall 20
- Mounting bracket 22
- Grounding the firewall 25
- Attaching the ring terminal 26
- Installing an MPU 27
- Installing a CF card 29
- Installing a fan tray 31
- Installing a power module 33
- Connecting interface cables 34
- Connecting Ethernet cables 35
- Connecting a power cord 36
- Connecting a DC power cord 37
- Verifying the installation 39
- Installing FRUs 40
- Required tools 42
- Installation procedure 42
- Installation precautions 43
- (3) Console cable 46
- Powering on the firewall 50
- Configuring services 55
- Configuring NAT 58
- Replacement procedures 61
- Removing a filler panel 62
- Installing a filler panel 63
- Replacing an MPU 64
- Replacing a CF card 67
- Replacing a power module 69
- Replacing a fan tray 70
- NOTE: 72
- Managing combo interfaces 77
- Rebooting your firewall 79
- Task Command 80
- Troubleshooting 81
- Service module failures 82
- Power supply system failures 83
- Fan failures 84
- Console port failure 85
- Password loss 86
- Cooling system failures 86
- Software upgrade failures 87
- Solution 88
- Symptom 88
- Chassis views 90
- Main processing unit 91
- Interface modules 92
- Power modules 93
- Fan tray 94
- Technical specifications 95
- NSQ1XP20 98
- Appendix B LEDs 101
- Interface module LEDs 103
- NSQ1GT8P40 104
- Power module LEDs 105
- Fan tray LEDs 106
- Arranging slots 107
- Numbering interfaces 107
- Examples 108
- Appendix D Cables 109
- Optical fiber 113
- Precautions 114
- General cabling requirements 115
- Cabling examples 118
Related products and manuals for Safety H3c-technologies H3C SecPath F5000-A5 Firewall
(26 pages)© 2020, manymanuals.com. All rights reserved. | 0.208 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals